Smart+ Aura Beam, Remote & Sensors

Installation, Pairing & Everyday Tips

1. How to Install

No tools. No drilling. Up in about 2 minutes.

Step 1

Insert the Battery

Look for the “” symbol on the battery and slide that end into the mount first.

Step 2

Attach the Aura Beams

Push each Aura Beam into the connectors on each end of the mount.

💡 Keep pushing until the ring is no longer visible, which means it is locked in place.
Step 3

Mount the Base

Works on any smooth, flat surface — tile, glass, metal, or painted walls.

1Make sure the wall is clean and dry; a quick wipe is enough.
2Peel the backing off the adhesive pad.
3Press to the wall and press hard for a full 30 sec.
4Wait 2 hours for it to bond and keep your hands off. Then twist each beam to the angle you like.
Press Hard — Full 30 Seconds
The adhesive bonds fully only under firm pressure, so a light press will let it fall.
Need to Move It?

Remove or Relocate

1Remove the Aura Beams and battery.
2Press & hold the base and pull the adhesive from the opening — straight down, slowly, a little at a time — so it stretches as it lets go.
✗Don’t rip it off in one quick pull; that is what damages paint.
✓Trace-free. Pulled slowly, it leaves no residue or marks, even on painted walls. Reinstall anytime with a new adhesive pad.

2. How to Use

Power

Press to turn on / off.

Brightness

Press & hold to brighten. Press & hold again to dim.

Color Temperature

Tap to switch: Warm (2700K) → Natural (4000K) → Daylight (6500K).
Press & hold for smooth adjustment.

Color Theme

Tap to switch: Aurora → Sunset → Forest → Ocean → Carnival.

Aurora
Colors drift slowly, like the northern lights
Sunset
Warm reds and oranges
Forest
Cool greens
Ocean
Deep to light blues
Carnival
Multi-color segments, fast switching

Lighting Modes

Tap to switch effects:

Breathing
light fades in and out
Music Sync
light responds to music
Steady
light stays constant
Works with both white light and color theme.

3. Battery & Charging

Charging

Charging the Battery

Snap the battery off and plug in any USB-C cable. Most phone and laptop chargers work, including PD fast charging (up to 20W).

Red flashing
Battery low — time to charge
Green flashing
Charging
Green solid
Fully charged
Swappable

Swappable Battery

The battery snaps right off while the light stays on the wall. Put in a charged spare to keep the light running 24/7.

🔋 Extra batteries are sold separately, and each one doubles as a PD 20W power bank.

4. Smart+ Remote

Sold separately.

Pair

Pair the Remote

1On the light, press & hold the “” for 3 seconds — the light flashes.
2Within 10 seconds, press & hold the remote’s “”.

Light goes steady, then fades off — paired.

💡 One remote can control multiple lights; repeat the pairing for each light.
↩️ Unpair: on the light, press & hold the “” for 7 seconds. Light brightens, then fades off.
Color Temperature

Warm to Daylight

Tap to switch: Warm (2700K) → Natural (4000K) → Daylight (6500K).

Then press & hold ‹·· / ··› to shift smoothly between warm and cool.

Brightness

Brighten or Dim

Press & hold Brightness + or − to adjust. Release to keep.

Color Theme

Five Themes, One Tap

Tap to switch: Aurora → Sunset → Forest → Ocean → Carnival.

Then tap ‹·· / ··› to move back and forth between themes.

Lighting Modes

Switch the Effect

Tap to switch: Breathing → Music Sync → Steady.

💡 Works with both white light and color theme.

5. How to Use the Smart+ Sensors

Sold separately. Pair it once and control your lights hands-free.

Pair First
1On the light, press & hold the “” button for 3 seconds until the light flashes.
2On the sensor, press & hold the Match / Modes button; its orange indicator stays lit during pairing.

The light turns steady, then fades out, and you are paired.

💡 A single sensor can run several lights, so pair each light separately. Best range: 66 ft / 20 m.
Unpair: on the light, press & hold the “” for 7 seconds; the light brightens, then fades out.
Installation Tips
  • Keep the sensor and lights within 66 ft / 20 m of each other.
  • Mount it at least 4 in / 10 cm off the floor to prevent signal loss.
  • Tilt the sensor head gently to get the best detection.
Smart+ Motion Sensor with numbered labels 1 to 4
1Motion DurationHow long it stays on after motion

Controls how long Aura Beam stays lit once it detects motion.

2ModesAuto 1 / Auto 2 / Always On / Off
Auto 1
Motion in the dark only
Flash 1×
Auto 2
Motion all day
Flash 2×
Always On
Light stays on
Flash 3×
Off
Lights off
—
3AdjustTemp (tap) • Brightness (hold)
Short press
Changes color temperature
Press & hold
Adjusts brightness
4Match / ModesPair (hold) • Lighting modes (press)
Hold
Pairs the sensor with an Aura Beam.
Press
Switches lighting modes: Breathing → Music Sync → Steady.
A sensor can pair with several lights in range, but each light accepts only one sensor at a time.
Smart+ Motion Sensor
Installation Tips
  • Keep the sensor and lights within 66 ft / 20 m of each other.
  • Mount it at least 4 in / 10 cm off the floor to prevent signal loss.
  • Tilt the sensor head gently to get the best detection.
Smart+ Motion Sensor with numbered labels 1 to 4
1Motion DurationHow long it stays on after motion

Controls how long Aura Beam stays lit once it detects motion.

2ModesAuto 1 / Auto 2 / Always On / Off
Auto 1
Motion in the dark only
Flash 1×
Auto 2
Motion all day
Flash 2×
Always On
Light stays on
Flash 3×
Off
Lights off
—
3AdjustTemp (tap) • Brightness (hold)
Short press
Changes color temperature
Press & hold
Adjusts brightness
4Match / ModesPair (hold) • Lighting modes (press)
Hold
Pairs the sensor with an Aura Beam.
Press
Switches lighting modes: Breathing → Music Sync → Steady.
A sensor can pair with several lights in range, but each light accepts only one sensor at a time.
Smart+ Hand Sensor
Installation Tips
  • Sweep your hand side-to-side (left ↔ right).
  • Avoid waving toward the sensor; front-to-back motion barely triggers it.
  • Sweep one time, then give every light a moment to react.
Smart+ Hand Sensor with numbered labels 1 to 4
1TimerOne-time auto-off for the next turn-on

Starts a one-time countdown that switches the light off after you turn it on.

2ModesAuto / Always On / Off
Auto
Hand-sweep control
Flash 1×
Always On
Light stays on
Flash 2×
Off
Lights off
—
3AdjustTemp (tap) • Brightness (hold)
Short press
Changes color temperature
Press & hold
Adjusts brightness
4Match / ModesPair (hold) • Lighting modes (press)
Hold
Pairs the sensor with an Aura Beam.
Press
Switches lighting modes: Breathing → Music Sync → Steady.
Smart+ Door Sensor
Installation Tips
  • The sensor sits on the side of the device. Position it so the door swings away from that side.
  • With the door closed, leave 0.2–0.59 in (5–15 mm) between it and the sensor side.
  • Do not mount it in the gap between double doors.
Smart+ Door Sensor with numbered labels
1ModesAuto / Always On / Off
Auto
Door open = on
Flash 1×
Always On
Light stays on
Flash 2×
Off
Lights off
—
2AdjustTemp (tap) • Brightness (hold)
Short press
Changes color temperature
Press & hold
Adjusts brightness
3Match / ModesPair (hold) • Lighting modes (press)
Hold
Pairs the sensor with an Aura Beam.
Press
Switches lighting modes: Breathing → Music Sync → Steady.

6. How to Recharge the Sensors

Two indicators, one cable. Here is what each light tells you.

Front Button Indicator
Sensor front view showing the button indicator
This front dot alerts you when the sensor needs a recharge.
USB-C side Charging Indicator
Sensor side view showing the USB-C port and charging indicator
This side dot reports the charging progress while connected.
What you’ll see

Low Battery Alert

Once the battery runs low, the front button indicator starts to blink orange.

Blinking orange = plug in a USB-C cable to charge.
While charging

Charging Status

Solid red = charging
Solid green = fully charged

The charging indicator is the small light beside the USB-C port.

Tip: Any regular USB-C power source will do (phone charger, power bank, laptop port).